View Profile: Brightonuk

01-23-2021, 04:19 PM

Brightonuk started a thread New Pads in General Tech

I am looking to upgrade my pads. The casting on the rear caliper is 0659/7 and stamped "Caterham" calipers on the front Any pointers to a good...

0 replies | 45 view(s)

01-22-2021, 04:02 PM

Brightonuk replied to a thread Motogadget M-Unit Blue in General Sevens Discussion

Yep finally got the M-ride to find the M-Unit I set the aux 2 to engage as soon as the ignition energizes so that is solved as I now have an Aux fuse...

60 replies | 11826 view(s)

01-20-2021, 07:06 PM

Brightonuk replied to a thread Motogadget M-Unit Blue in General Sevens Discussion

If you do go that route here is a good way to tin the wires I used it for any wires not terminated with Ferrules ...

60 replies | 11826 view(s)

01-20-2021, 10:03 AM

Brightonuk replied to a thread Motogadget M-Unit Blue in General Sevens Discussion

I started with these: ...

60 replies | 11826 view(s)

01-19-2021, 09:46 PM

Brightonuk replied to a thread Motogadget M-Unit Blue in General Sevens Discussion

Jeff OK I guess I must use a kill switch as "Lock" needs 12v to turn on the unit, so I will wire as you did using a hidden 12v switch. I am...

60 replies | 11826 view(s)

01-19-2021, 09:38 AM

Brightonuk replied to a thread Motogadget M-Unit Blue in General Sevens Discussion

Jeff As I am using an Aux out to trip a relay to the aux fuse box how do I get the M-Unit to send a signal as soon as it is turned on (without...

60 replies | 11826 view(s)

01-13-2021, 08:27 PM

Brightonuk replied to a thread T-9 Oil Plug in General Tech

I am off my meds As Ive been fretting over the gear oil the T9 was still on my mind The Zetec oil drain plug idiot :banghead:

3 replies | 176 view(s)

01-13-2021, 02:54 PM

Brightonuk started a thread T-9 Oil Plug in General Tech

Anyone know the thread size for the T-9 oil drain plug in addition the copper washer? Just changed my oil and I cant stop the leak from the drain...

3 replies | 176 view(s)

01-11-2021, 08:22 PM

Brightonuk replied to a thread Zetec sound? in General Tech

OK may not be a Zetec but this has gotta be the best recording of a Caterham engine (I would like to know where his mike was) ...

12 replies | 917 view(s)

01-07-2021, 08:11 PM

Brightonuk replied to a thread Zetec sound? in General Tech

My setup 2.0 Zetec overbored Not sure the specs on the overbore but running: JE Pistons 85mm Around a 11.1.Compression TMW Throttle Bodies...

12 replies | 917 view(s)

01-06-2021, 09:39 AM

Brightonuk replied to a thread Gear Oil in General Tech

As I said the hole concept will not work as there is a structural frame bar right in front of the plug Even with an allen cut down to a nub it is...

12 replies | 879 view(s)

01-05-2021, 09:30 PM

Brightonuk replied to a thread Gear Oil in General Tech

Thanks Mate saved me a lot of grief cause by ignorance going down the wrong path but is a bummer, I thought pull the lever fill from there it seemed...

12 replies | 879 view(s)

01-05-2021, 07:24 PM

Brightonuk replied to a thread Gear Oil in General Tech

The drill a hole concept does not work for we as the frame rail is dead center over the plug So if the car is level should I at least see oil in...

12 replies | 879 view(s)

01-05-2021, 05:47 PM

Brightonuk started a thread Gear Oil in General Tech

I was looking to change out the gear oil in my T9 using Redline MT-90 and as suggested going in via the top of the gear lever On removing the...

12 replies | 879 view(s)