Rotus Parts List.

[slngsht]

Lifted from Joe's yahoo Rotus user group...





>Parts List (http://www.usa7s.com/forum/uploads/slngsht/RotusPartsList.txt)

[slngsht]

tail light assemblies can be purchased here...



>http://www.man-a-fre.com/pa/taillights.htm (http://www.man-a-fre.com/pa/taillights.htm)



I called these folks and talked to a technical specialist on 805-578-8712 and found him to be very helpful and knowledgeable. He told me this was a '74 - '76 vintage part. I forgot to ask for the specific model application. In any event, they carry the complete lamp assembly or just the lens. Since I really need only the lens I ordered one at $14.95 plus shipping. Note that the original equipment part was "handed" but the replacement part will work on either the left hand or right hand side.This is true for the lamp assembly # 51550-60190 or just the lens.

[Old Yellow]

My tail lights aren't like the ones shown with the gasket problem.



Joe Worsley

[solder_guy]

As I continue to work on my Rotus I am updating my parts list here. Last updated Monday 1/17/2011

Front alignment
1/16 per side toe in
1/4 to 1/2 negative camber
3 degrees positive caster

Front ball joint grease fittings: NAPA . (SAE).

Rubber Nipple Covers for grease fittings and bleeder nipples: NAPA and junkyards.

-----------------------------------------------------

Rack and Pinion: '80-'82 Toyota Tercel. (shortened) (requires some grinding to fit the mouning blocks) (Note that the Rotus rack has a straight gear pinion whereas other OEM Toyota racks have a worm gear pinion which makes turning slower at the steering wheel)

Ratio: 21.7":1

Dust Boots for rack: (MOOG) MOK 9315 (left) MOK 9314 (right)

-----------------------------------------------------


My shocks: Koni 80Z 1669 (front and back) can be rebuild at Koni factory in Kentucky.


-----------------------------------------------------

Front wheel hub inner seal: '70-'73 Corona (not MKII)

Beck Arney 052-2128 (better quality), Timken 1178-S (Autozone)

Front inner bearing: L44549

Front outer bearing: LM11749


Front Caliper: Fenco C8500
$44.99 + $7 Core charge at Autozone

Caliper part numbers from eBay:
Toyota Corona 1970 - 1973 with Akebono brakes
new remanufactured left front brake caliper, part number FC697
new remanufactured right front brake caliper, part number FC696 or factory # 47710-21010

Front Caliper kit: Brakewear 66851 x2, $2.99 each side.

Front Pads: D48

Front Rotor: Aimco 3111, Bendix 141064, Raybestos 9010, Wagner BD97052, Min thinkness: 9mm.

All of the above apply to the '70-'73 Corona (not MKII)

----------------------------------------------------

FRONT:

Lower Ball Joint (four bolts): MOOG K8036 (ford)

Replacement Dust Cover for Moog K8036: C70Z-3A105B at Auto Krafters (800-228-7346) which must use the 4 bolt retaining ring.

Upper Ball Joint: MOOG ES150R for both the Ford F100, F250 '61-'66 also the K10 Chevy (note: not the ES150L ! )

Replacement Dust Cover for Moog ES150R: 9.13101 from energysspensionparts.com

http://www.energysuspensionparts.com/proddetail.asp?prod=9%2E13101

Replacement dust cover for Tie Rod End: Use a modern Toyota dust cover which is the same.

-----------------------------------------------------

The lug bolt pattern is 4 x114.3
Lug nut torque: 103 Newton-meters.
Lug Nuts:
Lug Nut Socket:

-----------------------------------------------------

My Front Turn Signal: 1973 Kawasaki Turn Signal Diagram (http://www.bikebandit.com/houseofmotorcycles/kawasaki-motorcycle-f11-f11-us-1973-turn-signals/o/m3419sch39081)

Housing: 569067-001
Amber Lens: 569175-001 "Stanley 045-6588"
Gasket: 569216-001
Complete unit: Kawasaki: 23037-005

-----------------------------------------------------

REAR:

late 1970s Corolla / Celica solid rear axle with drum brakes:

Rear Drum: 3541 (only number on box) 9" inner diameter x 1 5/8" wide brake surface.

Rear Shoes: PB407 9" diameter x 1 5/8" wide

Rear Drum Cylinder: Wagner F96845; Beck Arnley 072-3247.

Note: Lug Bolt Studs are shorter than what is found on the front hubs of the Rotus.. Longer Lug Bolt Studs can be acquired from junk yards. I got some out of a 1980 Toyota Pickup. This adds 5 threads of grip.

-----------------------------------------------------

REAR:
1979-1981 Toyota Supra "F" type solid rear axle with disc brakes.

If axle code ends in 3 then the differential is a LSD. (popular in Canada)

(The LSD guts from the '82-'85 Supra can be installed in the above axle. See Celicasupra.com LSD (http://forums.celicasupra.com/showthread.php?t=39145) in the MKI section.)
Disc Rotor: 31132
Disc Pads: DB196

Note: Lug Bolt Studs are shorter than what is found on the front hubs of the Rotus.. Longer Lug Bolt Studs can be acquired from junk yards. I got some out of a 1980 Toyota Pickup. This adds 5 threads of grip.

-----------------------------------------------------

REAR:

Clutch Master Cylinders (3): Beck Arney 072-1449 (for Toyota HILUX Pickup Truck '70-'74).

----------------------------------------------------

Original Hood Latches .. found on the early Rotus and Lotus Sevens:
Grayston GE64 "Bonnet Toggle" Hood Latches (UK) (eBay)

----------------------------------------------------

Joe's Original Rotus Parts List from first post link:

Tail Light (LH) (Toyo) 81550-60190
Tail Light (RH) (Toyo) 81560-60110
Rear Tag Light (Toyo) 81270-19276
Headlight SW (Toyo) 84110-12050
Four Way Flasher SW (Toyo) 84330-12040-86
Front Turn Signal (Harley Davidson)
Wiper SW (Toyo)84650-12020
Indicator Lights (Ron Francis) ???
Mirrors (Honda) 88 110 MG8-770 Left
88 120 MG8-770 Right
Pedal Assy (Tilton)72-623 (69-2)
Speedo Cable 83710-29345
Steering Rack (Toyo) 81 & up Tercell 88 Tercell 2TC engine????
Steering Rack Boot (large) (Toyo)90461-10273
Steering Rack Boot (small) (Toyo)90467-18003
Steering Flex Spring Pinto or Bobcat
Upper Rod Ends Ball & Thread Rod (Big A) PRC ES 150R Ford F250 61-66
K10 Chevy E5150R
Lower Ball Joints (Big A)PRC 10230
(Seal Power) 801-11230
(Moog) K 8036
Emergency Brake Cable (Toyo) 79 Supra LR
Front Spindles & Rotors (Toyo) 70-73 Corona
Front Brake Calipers & Pads (Toyo)70-73 Corona
Master Cylinder (clutch & brake) (Toyo)31410-14091 76 & 77 Celica EIS E98224 ??
31410-1271 ????
Spring Wrapped Brake Hoses (Toyo)90947-02317-86
Stop Light SW (Big A)325-6 US14std
Banjo Bolt (Toyo)90401-10047
Banjo Bolt Washer (Toyo)90430-10074
Banjo T (Toyo)90405-10073
Brake Line T (Toyo)90413-10098

Wiper Motor (VW BUG)
Wiper Arm (NAPA)60-722
Wiper Blade (Beck/Arnly)193-8208
Windshield to Body Rubber (3M) 2115
Radiator 21" Mazda


FRONT BRAKES
Front Brake Pads (Toyo)04491-14011 70-74 corona 2Tc 1600cc eng. ??
Seals (Toyo)90311-40108
Caliper Rebuild Kit (Toyo)04479-14010
Rebuilt Caliper R/H (Toyo)47730-20030-84
Rebuilt Caliper L/H (Toyo)47750-20020-84
Rotor (Toyo)43512-20032
Hub Inner Bearing (Toyo)90368-26013
Hub Seal (Toyo)90311-40108
Hub Outer Bearing (Toyo)90368-17017
Hub Washer (Toyo)90214-16910
Hub Nut Retainer (Toyo)43525-20011
Hub Nut (Toyo)43514-20010

REAR AXLE ASSY (Supra 79-81) (Cressida,w/disc brakes)7.7" ring gear
Limited Slip Unit (TRD)41301-RA002 81 supra ??
Limited Slip Bearings (TRD)90368-50024
Axle Seal (Toyo)90311-52059
Brake Pads (Toyo)04492-14041
Caliper Kit (Toyo)04479-14051
Brake Hoses (Toyo) 9640-32605 Bendix 77260

REAR AXLE (Corolla GTS 76-79)
Brake Pad (Toyo)04492-19030
Caliper Rebuild Kit (Toyo)04479-12110
Brake Hose (Toyo)96940-32555
Axle Seals (Toyo)96940-32555
Emergency Brake Handle (Mazda RX 2-3-4 or GLC
Shocks Koni 802091
Motor Mount (4cyl) (Big A)2-4106
Motor Mount (Mazda Turbo) (Big A)2-2123
Motor Mount (V8) (Big A)2-2224
Motor Mount (V8) (Big A)2-2218

[solder_guy]

Website for Toyota Axles: http://www.norbie.net/toyotaaxle/

As an example of how to decipher Toyota axle codes:

The '80 Supra from which I grabbed the solid rear axle has code "F312" which corresponds to:
a 7.5" Ring Gear, a 3.909 gear ratio, and 2 pinions with no LSD.

MA47 Solid Axle (coils) F312: 7.5", 3.90:1, 2 pinions, Open 4x114.3 1410mm Solid disc, 1 piston calipers, integrated drum handbrake

Corolla:
TE71 Solid Axle (coils) S312: 6.4", 3.90:1, 2 pinions, Open 4x114.3 1410mm Drum

Rob

Copied from celicasupra.com (http://www.celicasupra.com):

check the firewall vin plate.
-----------------------------------------------------

First Digit: (Ring Gear Diameter)
Second & Third Digits: (Gear Ratio)
Fourth Digit: (# of Pinion Gears ... Limited Slip (yes/no)

-----------------------------------------------------

A = 138 mm
B = 145 mm
C = 6.25 "
D = 6.62"
E = 7.1"
F = 7.5"
G = 8"
H = 9"
J = 9.25"
K = 9.5"
L = 10.5"
M = 12.5"
N = 13.5"
P = 14"
R = 162 mm
S = 6.38"
T = 6.7"
U = 6"
V = 10.6"
W = 15.5"
X = 142 mm
Y = 158 mm

-----------------------------------------------------

01 = 3.30
02 = 3.36
03 = 3.545
04 = 3.556
05 = 3.70
06 = 3.889
07 = 3.90
08 = 4.111
09 = 4.222
10 = 4.375
11 = 4.444
12 = 4.625
13 = 4.79
14 = 4.875
15 = 5.125
16 = 5.286
17 = 5.60
18 = 5.714
19 = 5.833
20 = 6.167
21 = 6.667
22 = 6.78
23 = 6.833
24 = 7.64
25 = 4.556
26 = 5.571
27 = 3.364
28 = 4.30
29 = 4.10
30 = 3.727
31 = 3.909
32 = 6.591 or 5.583
33 = 7.503 or 5.583
34 = 6.781 or 4.786
35 = 7.636 or 5.60
36 = 4.778
37 = 3.583
38 = 3.417

-----------------------------------------------------

2 = 2 Pinions/No LSD
3 = 2 Pinions /Yes LSD
4 = 4 Pinions/No LSD (4WD)
5 = 4 Pinions/Yes LSD (4WD)

[solder_guy]

Bump .. to show that I have updated my list of Rotus parts above.

Rob Mitchell

[slngsht]

Any idea what the radiator is from? the list simply says Mazda

[solder_guy]

Any idea what the radiator is from? the list simply says Mazda

Mazda mazda! :)

Actually I have no idea .. there's some creative plumbing for my engine to the radiator .. They did not go with the standard Toyota radiator for my Toyota 2TG engine ...

Rob

[slngsht]

I know I had nothing to do with it. :D

Mine seems to be significantly modded - it fits the nose cone PERFECTLY. Unfortunately it has developed a few leaks.